document number: 42017 for technical questions, contact: spresale@vishay.com www.vishay.com revision: 16-feb-07 25 type 418p vishay sprague polyester capacitors filmite ? ?e?, orange drop ? , radial lead features ? identical performance characteristics to type 225p pressed polyester capacitors through 600 wvdc ratings ? wound from petp polyester film and thin gauge foil under carefully controlled atmospheric conditions ? protected against moisture by a conformal coating of epoxy ? specifically designed for printed wiring board applications ? widely used in computers, instrumentation and telecommunications equipment performance characteristics operating temperature: - 55 c to + 85 c, standard; up to + 105 c when wvdc is reduced to 70 % of + 85 c rating. to + 125 c when wvdc is 50 % of + 85 c rating. insulation resistance: after a 2 minute charge at rated voltage or 500 v, whichever is less. at + 25 c: 100 000 megohm for c 0.25 microfarads 25000 megohm - microfarads for c > 0.25 microfarads at + 85 c: 10 000 megohm for c 0.15 microfarads 1500 megohm - microfarads for c > 0.15 microfarads at + 105 c: 1500 megohm for c 0.17 microfarads 250 megohm - microfarads for c > 0.17 microfarads at + 125 c: 200 megohm for c 0.13 microfarads 25 megohm - microfarads for c > 0.13 microfarads capacitance tolerance an d dissipation factor: capacitors shall be measured at a frequency for 1000 hz at + 25 c or else be referred to measurements made at that frequency and temperature. t he maximum dissipation factor shall be 0.75 %. dielectric withst anding voltage: capacitors rated below 1000 volts shall withstand a dc potential of 250 % of rated voltage applied between terminals for not more than 5 seconds. capacitance rated 1000 volts and above shall withstand a dc potential of 200 % of rated voltage applied between the terminals for not more than 5 seconds. the test voltage must be applied and discharged through a resistor of 1 ohm per volt. humidity test: condition capacitors with no voltage applied for 72 hours at 95 % relative humidity and + 75 c. remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. measure insulation resistance after a 2 minute charge at 25 c and rated voltage or 500 vdc, whichever is less. minimum product of insulation resistance and capacitance shall be 5000 megohm - microfarads after test but need not exceed 10 000 megohm. not more than one failure allowed in 12 units tested. dc life test: capacitance are capable of wit hstanding a 500 hour life test at + 85 c at 150 % of rate d working voltage. after test, capacitance shall not have changed by more than 5 % of initial value, insulation resistance shall not have decreased by more than 50 % of the initial limit and dissipation factor shall not have increased to more than 1 %. rohs compliant dimensions in inches [millimeters] case code l (max.) s terminal a and b terminal d j 0.70 [17.78] 0.500 [12.700] 0.375 [9.525] k 0.90 [22.86] 0.688 [17.475] 0.375 [9.525] l 1.20 [30.48] 0.969 [24.613] 0.719 [18.263] m 1.60 [40.64] 1.344 [34.138] 1.094 [27.788] 1.250 [31.750] min. 0.237 [6.019] max. l max. s 0.060 [1.524] terminal a l max. 0.237 [6.019] max. lead len g th s 0.030 [0.762] terminal b l max. 0.237 [6.019] max. lead len g th 0.032 [0. 8 13] dia. (no. 20 awg) tinned copper-clad steel d max. s 0.030 [0.762] terminal d
www.vishay.com for technical question s, contact: spresale@vishay.com document number: 42017 26 revision: 16-feb-07 type 418p vishay sprague polyester capacitors filmite ? ?e?, orange drop ? , radial lead * these standard ratings are available through sprague ? distribution on special order. for complete part number, add letter and number for terminal and lead length in accordance with how to order (ex: 418p47492md3). ** 60 hz rms capacitance change - 55 - 40 - 25 0 + 25 + 50 + 75 + 8 5 + 105 + 125 - 50 + 100 16 14 12 !0 8 6 4 2 0 2 4 6 z h 0 0 0 1 / e g n a h c e c n a t i c a p a c % capacitance change envelope for 96 % confidence level temperature deg. centigrade dissipation factor vs. temperature typical z h 0 0 0 1 / n o i t a p i s s i d % - 55 - 40 - 25 0 + 25 + 50 + 75 + 8 5 + 105 + 125 - 50 + 100 temperature deg. centigrade 1.5 1.0 .5 0 standard ratings* f 10 % tolerance part number size lh 100 vdc/70 vac** 0.027 418p27391j 0.70 [17.78] 0.35 [8.89] 0.033 418p33391j 0.70 [17.78] 0.35 [8.89] 0.047 418p47391j 0.70 [17.78] 0.35 [8.89] 0.082 418p82391k 0.90 [22.86] 0.40 [10.16] 0.1 418p10491k 0.90 [22.86] 0.40 [10.16] 0.15 418p15491k 0.90 [22.86] 0.45 [11.43] 0.22 418p22491l 1.20 [30.48] 0.45 [11.43] 0.33 418p33491l 1.20 [30.48] 0.50 [12.70] 0.47 418p47491m 1.60 [40.64] 0.50 [12.70] 0.68 418p68491m 1.60 [40.64] 0.60 [15.24] 1.0 418p10591m 1.60 [40.64] 0.70 [17.78] 200 vdc/140 vac** 0.0056 418p56292j 0.70 [17.78] 0.33 [8.38] 0.0068 418p68292j 0.70 [17.78] 0.33 [8.38] 0.01 418p10392j 0.70 [17.78] 0.33 [8.38] 0.015 418p15392j 0.70 [17.78] 0.33 [8.38] 0.018 418p18392j 0.70 [17.78] 0.33 [8.38] 0.022 418p22392j 0.70 [17.78] 0.33 [8.38] 0.033 418p33392k 0.90 [22.86] 0.38 [9.65] 0.039 418p39392k 0.90 [22.86] 0.38 [9.65] 0.047 418p47392k 0.90 [22.86] 0.38 [9.65] 0.056 418p56392l 1.20 [30.48] 0.38 [9.65] 0.068 418p68392l 1.20 [30.48] 0.38 [9.65] 0.082 418p82392l 1.20 [30.48] 0.40 [10.16] 0.1 418p10492l 1.20 [30.48] 0.40 [10.16] 0.15 418p15492l 1.20 [30.48] 0.45 [11.43] 0.22 418p22492l 1.20 [30.48] 0.50 [12.70] 0.27 418p27492m 1.60 [40.64] 0.47 [11.94] 0.33 418p33492m 1.60 [40.64] 0.47 [11.94] 0.47 418p47492m 1.60 [40.64] 0.55 [13.97]
type 418p polyester capacitors filmite ? ?e?, orange drop ? , radial lead vishay sprague document number: 42017 for technical questions, contact: spresale@vishay.com www.vishay.com revision: 16-feb-07 27 * these standard ratings are available through sprague ? distribution on special order. for comple te part number, add letter and number for terminal and lead length in accordance wi th how to order (ex: 418p47492md3). ** 60 hz rms standard ratings* in inches [millimeters] f 10 % tolerance part number size lh 400 vdc/200 vac** 0.001 418p10294j 0.70 [17.78] 0.30 [7.62] 0.0015 418p15294j 0.70 [17.78] 0.30 [7.62] 0.0022 418p22294j 0.70 [17.78] 0.30 [7.62] 0.0033 418p33294j 0.70 [17.78] 0.30 [7.62] 0.0047 418p47294j 0.70 [17.78] 0.30 [7.62] 0.0068 418p68294j 0.70 [17.78] 0.33 [8.38] 0.0082 418p82294j 0.70 [17.78] 0.35 [8.89] 0.01 418p10394j 0.70 [17.78] 0.35 [8.89] 0.015 418p15394j 0.70 [17.78] 0.38 [9.65] 0.018 418p18394k 0.90 [22.86] 0.38 [9.65] 0.022 418p22394k 0.90 [22.86] 0.38 [9.65] 0.033 418p33394k 0.90 [22.86] 0.40 [10.16] 0.047 418p47394l 1.20 [30.48] 0.40 [10.16] 0.056 418p56394l 1.20 [30.48] 0.45 [11.43] 0.068 418p68394l 1.20 [30.48] 0.45 [11.43] 0.082 418p82394l 1.20 [30.48] 0.52 [13.21] 0.1 418p10494l 1.20 [30.48] 0.52 [13.21] 0.15 418p15494l 1.20 [30.48] 0.57 [14.48] 0.18 418p18494m 1.60 [40.64] 0.60 [15.24] 0.22 418p22494m 1.60 [40.64] 0.60 [15.24] 0.27 418p27494m 1.60 [40.64] 0.65 [16.51] 0.33 418p33494m 1.60 [40.64] 0.65 [16.51] 0.39 418p39494m 1.60 [40.64] 0.72 [18.29] 0.47 418p47494m 1.60 [40.64] 0.80 [20.32] 600 vdc/200 vac** 0.001 418p10296j 0.70 [17.78] 0.30 [7.62] 0.0012 418p12296j 0.70 [17.78] 0.33 [8.38] 0.0015 418p15296j 0.70 [17.78] 0.33 [8.38] 0.0018 418p18296j 0.70 [17.78] 0.33 [8.38] 0.0022 418p22296j 0.70 [17.78] 0.33 [8.38] 0.0027 418p27296j 0.70 [17.78] 0.35 [8.89] 0.0033 418p33296j 0.70 [17.78] 0.35 [8.89] 0.0039 418p39296j 0.70 [17.78] 0.38 [9.65] 0.0047 418p47296j 0.70 [17.78] 0.38 [9.65] 0.0056 418p56296j 0.70 [17.78] 0.40 [10.16] 0.0068 418p68296j 0.70 [17.78] 0.40 [10.16] 0.0082 418p82296k 0.90 [22.86] 0.40 [10.16] 0.01 418p10396k 0.90 [22.86] 0.40 [10.16] 0.012 418p12396k 0.90 [22.86] 0.40 [10.16] 0.015 418p15396k 0.90 [22.86] 0.40 [10.16] 0.018 418p18396k 0.90 [22.86] 0.45 [11.43] 0.022 418p22396k 0.90 [22.86] 0.45 [11.43] 0.027 418p27396l 1.20 [30.48] 0.45 [11.43] 0.033 418p33396l 1.20 [30.48] 0.45 [11.43] 0.039 418p39396l 1.20 [30.48] 0.55 [13.97] 0.047 418p47396l 1.20 [30.48] 0.55 [13.97] 0.056 418p56396l 1.20 [30.48] 0.60 [15.24] 0.068 418p68396l 1.20 [30.48] 0.60 [15.24] 0.082 418p82396l 1.20 [30.48] 0.65 [16.51] 0.1 418p10496l 1.20 [30.48] 0.65 [16.51] 0.12 418p12496m 1.60 [40.64] 0.70 [17.78] 0.15 418p15496m 1.60 [40.64] 0.70 [17.78] 0.18 418p18496m 1.60 [40.64] 0.80 [20.32] 0.22 418p22496m 1.60 [40.64] 0.80 [20.32] 0.25 418p25496m 1.60 [40.64] 0.80 [20.32]
www.vishay.com for technical question s, contact: spresale@vishay.com document number: 42017 28 revision: 16-feb-07 type 418p vishay sprague polyester capacitors filmite ? ?e?, orange drop ? , radial lead * these standard ratings ar e available through sprague ? distribution on special order. for comp lete part number, add letter and number for terminal and lead length in accordance with how to order (ex: 418p47492md3) ** 60 hz rms standard ratings in inches [millimeters] f 10 % tolerance part number size lh 1000 vdc/200 vac** 0.001 418p102910j 0.70 [17.78] 0.33 [8.38] 0.0015 418p152910j 0.70 [17.78] 0.33 [8.38] 0.0018 418p182910j 0.70 [17.78] 0.35 [8.89] 0.0022 418p222910j 0.70 [17.78] 0.35 [8.89] 0.0033 418p332910k 0.90 [22.86] 0.35 [8.89] 0.0047 418p472910k 0.90 [22.86] 0.40 [10.16] 0.0056 418p562910k 0.90 [22.86] 0.43 [10.92] 0.0068 418p682910k 0.90 [22.86] 0.43 [10.92] 0.0082 418p822910k 0.90 [22.86] 0.48 [12.19] 0.01 418p103910k 0.90 [22.86] 0.48 [12.19] 0.015 418p153910l 1.20 [30.48] 0.48 [12.19] 0.018 418p183910l 1.20 [30.48] 0.58 [14.73] 0.022 418p223910l 1.20 [30.48] 0.58 [14.73] 0.027 418p273910l 1.20 [30.48] 0.65 [16.51] 0.033 418p333910l 1.20 [30.48] 0.65 [16.51] 0.039 418p393910m 1.60 [40.64] 0.65 [16.51] 0.047 418p473910m 1.60 [40.64] 0.65 [16.51] 0.056 418p563910m 1.60 [40.64] 0.75 [19.05] 0.068 418p683910m 1.60 [40.64] 0.75 [19.05] 0.082 418p823910m 1.60 [40.64] 0.85 [21.59] 0.1 418p104910m 1.60 [40.64] 0.85 [21.59] ordering information 418p 104 9 1 j, k, l or m d 3 (-xxx) type capacitance tolerance dc voltage rating case code terminal lead length special construction capacitance is expressed in picofarads. the first two digits are significant. the third is the number of zeros to follow. values must conform to decade rating for the tolerance specified. 0 = 20 % 9 = 10 % 5 = 5 % this is expressed in hundred of volts. see dimensional configurations a = straight lead b = hairpin crimped d = hockey crimped 1 = 0.187" 0.030" [4.750 0.762] 2 = 0.250" 0.030" [6.350 0.762] 3 = 1.250" [31.750] minimum a three-digit suffix may be added by the factory to denote special construction.
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
